82141 • Safety CAUTION: Read, understand and • Operation follow Safety Rules and Operating Instructions in this manual before • Maintenance using this product. • Espafiol © Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Www.craftsman.com 070606. • r:_:] i:[o]|o[o] _/ / _ _/ 1_ Page Warranty Safety Instructions Safety Symbols Control and Jacks Symbols and Annunciators Specifications Battery Installation Operating Instructions DC Voltage Measurements AC Voltage Measurements DC Current Measurements AC Current Measurements Resistance Measurements Continuity Check Diode Test. • Manual Ranging MultiMeter fails togive complete satisfaction within o ne year from the date ofpurchase, RETURN ITTO THE NEAREST SEARS STORE OR OTHER CRAFTSMAN OUTLET THE UNITED STATES, and Sears will r eplace it,free ofcharge. Ifthis CRAFTSMAN Manual Ranging MultiMeter. • This meter has been d esigned forsafe use, but m ust beoperated with caution. View and Download Craftsman 82141 owner's manual online. 82141 Multimeter pdf manual download. Clamp-on ammeter/ digital multimeter (12 pages). Mantenimiento Instrucciones de operaci6n en este manual antes de usar el producto. Si este Multimetro de escala manual CRAFTSMAN no le satisface totalmente. The rules l isted b elow m ust be carefully followed forsafe o peration. NEVER apply voltage orcurrent tothe meter that e xceeds specified maximum: Input Limits Function Maximum. • 3_'I _ I=II l i'db_'d;4:[o]l This symbol adjacent to another symbol, terminal or operating device indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to the meter. L WARN,NG This WARNING symbol indicates a potentially hazardous situation, which if not avoided, could result. • o_o]_IIII_,To] L',]F:I _Ie]LnlT:T_ [(_ LCD Display Function switch COM jack 10A jack Positive jack Note: Tilt stand, fuse and battery compartment are on rear of unit. H =O __k,| __ k, k, __ O_ •))) Continuity Diode test milli ( volts, amps) kilo (ohms) £_ ohms. • Function Resolution Range Accuracy 200mV 0.1mV DC Voltage 2000mV (V DC) 0.01V +(0.5% reading + 2 digits) 200V 0.1V 600V 200V 0.1V AC Voltage +(1.5% reading + 5 digits 600V (V AC) (50/60Hz) DC Current 200mA 100pA +(1.2% reading + 2 digits) 10mA (A DC) +(2.0% reading + 2 digits) • Diode T est Test current of 1 mA maximum, open circuit voltage 2.8V DC typical Continuity Check Audible signal will sound if the resistance is less than approximately 30£2 Battery Test current 9V (6mA); 1.5V (100mA) >1M£2 Input Impedance ACV Bandwidth 45Hz to 450Hz 200mV DCA voltage. The diagram (below) indicates five of the most common serial number locations. Specialized bike serial number lookup. If there is no serial number near the cranks, you should check other common places including the front headset or rear stays. Turn your bike upside down and record the number. Background animasi bergerak powerp…. • I WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery door. Disconnect the test leads from the meter. Remove the protective rubber holster (if installed)_._t Open the battery door by loosening the screw using a Phillips head screwdriver. • J WARNING: Risk of electrocution. High-voltage circuits, both AC and DC, J are very dangerous and should be measured with great care. ALWAYS turn the function switch to the OFF position when the meter is not in use. ![]() If '1' appears in the display during a measurement, the value exceeds the range you have selected. • AC VOLTAGE MEASUREMENTS WARNING: Risk of Electrocution. The probe tips may not be long enough to contact the live parts inside some 240V outlets for appliances because the contacts are recessed deep in the outlets. As a result, the reading may show 0 volts when the outlet actually has voltage on it. • DC CURRENT MEASUREMENTS longer than 30 seconds. Exceeding 30 seconds may cause damage to I CAUTION: Do not make current measurements on the 10A scale for the meter and/or the test leads. Insert the black test lead banana plug into the negative (COM) jack. • AC CURRENT MEASUREMENTS longer than 30 seconds. Exceeding 30 seconds may cause damage to I CAUTION: Do not make current measurements on the 10A scale for the meter and/or the test leads. Insert the black test lead banana plug into the negative (COM) jack. • RESISTANCE MEASUREMENTS test and discharge all capacitors before taking any resistance ARNING: To avoid electric shock, disconnect power to the unit under measurements.
0 Comments
Leave a Reply. |